Reconfigurable Intelligent Surfaces (RISs) are regarded as promising enablers of smart radio environments, since they allow the electromagnetic response of the propagation medium to be engineered in a programmable manner. Their relevance extends from Sub-6 GHz systems to higher-frequency mmWave and sub-THz platforms, where controllable wave manipulation can support coverage enhancement, beam steering, and adaptive shaping of propagation conditions. However, the practical advancement of RIS technology depends not only on electromagnetic design, but also on the availability of hardware platforms that can be effectively controlled, fabricated, and experimentally assessed. This thesis investigates reflective programmable surfaces in two complementary frequency domains. The first research line concerns a Sub-6 GHz RIS, from the periodic full-wave analysis of the adopted meta-atom to the design and fabrication of a representative two-cell PCB prototype for characterization in a WR284 rectangular waveguide, and to the development of an 8×8 metasurface prototype with its dedicated control hardware. Waveguide measurements on the two-cell prototype confirm the voltage-controlled tunability of the element, with a measured phase variation close to 180°. In parallel, the adoption of an FPGA-based architecture overcomes the update-rate limitations of the baseline serial control chain and supports deterministic high-speed reconfiguration toward MHz-class operation. The second research line concerns a liquid-crystal-based reflective metasurface for mmWave/sub-THz operation and addresses both electromagnetic and hardware challenges. Full-wave simulations are first carried out on the LC-loaded unit cell to identify suitable operating conditions, and are then extended to the metasurface scale, to predict the far-field response under different coding sequences. On the hardware side, the work includes the comparative assessment of commercial solutions, the selection of a suitable biasing architecture, and the development of firmware for the generation of the low-frequency bipolar square-wave excitation required for LC actuation. Particular attention is devoted to synchronized multi-channel switching in order to avoid channel-to-channel timing skew. Preliminary experimental tests are carried out on the first fabricated prototypes through specular-reflection and bistatic radar-cross-section measurements under different coding sequences, providing an initial experimental assessment of the proposed concept. Overall, the thesis provides a hardware-oriented perspective on RIS implementation across two complementary frequency regimes, showing how electromagnetic design, biasing strategy, control electronics, and experimental assessment must be jointly adapted to the operating band.
Design, Development, and Experimental Validation of Reconfigurable Intelligent Surfaces for Sub-6 GHz and mmWave Smart Radio Environments / Monaco, F.P.. - (2026 Oct 07).
Design, Development, and Experimental Validation of Reconfigurable Intelligent Surfaces for Sub-6 GHz and mmWave Smart Radio Environments
francesco pio monaco
2026-10-07
Abstract
Reconfigurable Intelligent Surfaces (RISs) are regarded as promising enablers of smart radio environments, since they allow the electromagnetic response of the propagation medium to be engineered in a programmable manner. Their relevance extends from Sub-6 GHz systems to higher-frequency mmWave and sub-THz platforms, where controllable wave manipulation can support coverage enhancement, beam steering, and adaptive shaping of propagation conditions. However, the practical advancement of RIS technology depends not only on electromagnetic design, but also on the availability of hardware platforms that can be effectively controlled, fabricated, and experimentally assessed. This thesis investigates reflective programmable surfaces in two complementary frequency domains. The first research line concerns a Sub-6 GHz RIS, from the periodic full-wave analysis of the adopted meta-atom to the design and fabrication of a representative two-cell PCB prototype for characterization in a WR284 rectangular waveguide, and to the development of an 8×8 metasurface prototype with its dedicated control hardware. Waveguide measurements on the two-cell prototype confirm the voltage-controlled tunability of the element, with a measured phase variation close to 180°. In parallel, the adoption of an FPGA-based architecture overcomes the update-rate limitations of the baseline serial control chain and supports deterministic high-speed reconfiguration toward MHz-class operation. The second research line concerns a liquid-crystal-based reflective metasurface for mmWave/sub-THz operation and addresses both electromagnetic and hardware challenges. Full-wave simulations are first carried out on the LC-loaded unit cell to identify suitable operating conditions, and are then extended to the metasurface scale, to predict the far-field response under different coding sequences. On the hardware side, the work includes the comparative assessment of commercial solutions, the selection of a suitable biasing architecture, and the development of firmware for the generation of the low-frequency bipolar square-wave excitation required for LC actuation. Particular attention is devoted to synchronized multi-channel switching in order to avoid channel-to-channel timing skew. Preliminary experimental tests are carried out on the first fabricated prototypes through specular-reflection and bistatic radar-cross-section measurements under different coding sequences, providing an initial experimental assessment of the proposed concept. Overall, the thesis provides a hardware-oriented perspective on RIS implementation across two complementary frequency regimes, showing how electromagnetic design, biasing strategy, control electronics, and experimental assessment must be jointly adapted to the operating band.I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.


